Abstract In this paper the instructions for preparing camera ready paper for International Conference memstech 2013 are given
Скачати 19.87 Kb.
|
|
Preparing the Camera Ready Paper for Proceedings of International Conference MEMSTECH 2013 Pavlo Denysyuk1, Andriy Kernytskyy1, Oleg Hryciv2 1. CAD Department, Lviv Polytechnic National University, UKRAINE, Lviv, S. Bandery street 12, E-mail: denysyuk@polynet.lviv.ua, kernitsky@gmail.com 2. CSD Department, Lviv Polytechnic National University, UKRAINE, Lviv, S. Bandery street 12, E-mail: ohryciv@gmail.com Abstract - In this paper the instructions for preparing camera ready paper for International Conference MEMSTECH 2013 are given. Keywords - Camera ready paper, Conference Proceedings, MEMSTECH 2013. I. Introduction In order of effect high quality of MEMSTECH 2013 Conference Proceedings the authors are requested to follow instruction given in this sample paper. Length of papers are from 1 to 20 full pages. II. Instruction for Authors Times New Roman 10 pt font should be used for normal text. The normal line spacing is 1.5 times of the font size. Please, equalize the length of the columns on the last page. Paragraph should be indented 3.5mm. Manuscript have to be prepared in two column separated by 5mm. The margins for A4 (210x297) are given in Table 1. TABLE 1 Page layout description
Title must be written using 22pt font, centered. The spacing between title and authors line is 6mm. Author's names (without affiliation) should be typed using 14pt font. Author's affiliation (institution, address, E-mail) should be given in the bottom of the first column using 9pt font. In the beginning of the paper abstract and keywords should be given. Abstract should be about 50 words. It is desirable to up 5 keyword. Please, use 9pt bold font for abstract and keywords and 9pt italic for the words "Abstract" and "Keywords". Paper text may be divided in a number of sections. Section tiles should be typed using 12pt font in Small Caps Option. For numbering use Roman number. The space after section and between the last section and the next section title are 5mm. Equations should be centered and labeled. The example of equation is Eq. 1:  (1)Larger equation must be split in multiple lines. Tables should be made as one column. In rare case it allowed to use two column tables in the top of the page. Tables must have caption located above the table. Table captions should be written using 9pt Small Caps font. Figures also should be one column wide. If it impossible using two column wide figures is allowed but in that case figure must be located in the top of the page. Please do not use photocopies. Each figure must have a caption under the figure. For figure captions 9pt should be used.  Fig.1 System function. When your refer to an equation, a figure, a table, a section or literature references in the text of the paper please use the following expressing: Eq. (1), Eqs. (1) and (2), Fig. 1, Figs. 1 and 2, Table I, Tables I and II, Section I, [1], [2]. The examples for the referencing a journal paper, a conference paper, and book according to IEEE Transactions format are given. References [1] P. B. Johns, "A symmetrical condensed node for the TLM method," IEEE Trans. Microwave Theory Tech., vol. MTT-35, pp.370-377, Apr. 1997. [2] V. Trenkic, C. Christopoulos, and T.M. Benson, "Efficient computational algorithms for TLM," in 1st Int. Workshop TLM, Univ. Victoria, Canada, Aug. 1995, pp. 77-80. [3] C. Christopoulos, The transmission-Line Modeling (TML) Method. Piscataway, NJ: IEEE Press, 1995. III. Conclusion In this paper the instructions for preparing camera ready paper for including in the Proceedings of International Conference MEMSTECH 2013 is given. |
